This MedLibrary.org supplementary page on Permeability (fluid) is provided directly from the open source Wikipedia as a service to our readers. Please see the note below on authorship of this content, as well as the Wikipedia usage guidelines. To search for other content from our encyclopedia supplement, please use the form below:
Related Sponsors
 |
This article needs additional citations for verification. Please help improve this article by adding reliable references. Unsourced material may be challenged and removed. (April 2008) |
Permeability in the earth sciences (commonly symbolized as κ, or k) is a measure of the ability of a material (typically, a rock or unconsolidated material) to transmit fluids. It is of great importance in determining the flow characteristics of hydrocarbons in oil and gas reservoirs, and of groundwater in aquifers. It is typically measured in the lab by application of Darcy's law under steady state conditions or, more generally, by application of various solutions to the diffusion equation for unsteady flow conditions.1
Contents |
Formula
The intrinsic permeability of any porous material is:
where
- κI is the intrinsic permeability [L2
- C is a dimensionless constant that is related to the configuration of the flow-paths
- d is the average, or effective pore diameter [L]
Permeability needs to be measured, either directly (using Darcy's law) or through estimation using empirically derived formulas.
A common unit for permeability is the darcy (D), or more commonly the millidarcy (mD) (1 darcy 
10−12m2). Other units are cm2 and the SI m2.
Permeability is part of the proportionality constant in Darcy's law which relates discharge (flow rate) and fluid physical properties (e.g. viscosity), to a pressure gradient applied to the porous media. The proportionality constant specifically for the flow of water through a porous media is the hydraulic conductivity; permeability is a portion of this, and is a property of the porous media only, not the fluid. In naturally occurring materials, it ranges over many orders of magnitude (see table below for an example of this range).
For a rock to be considered as an exploitable hydrocarbon reservoir without stimulation, its permeability must be greater than approximately 100 mD (depending on the nature of the hydrocarbon - gas reservoirs with lower permeabilities are still exploitable because of the lower viscosity of gas with respect to oil). Rocks with permeabilities significantly lower than 100 mD can form efficient seals (see petroleum geology). Unconsolidated sands may have permeabilities of over 5000 mD.
Tensor permeability
To model permeability in anisotropic media, a permeability tensor is needed. Pressure can be applied in three directions, and for each direction, permeability can be measured (via Darcy's law in 3D) in three directions, thus leading to a 3 by 3 tensor. The tensor is realized using a 3 by 3 matrix being both symmetric and positive definite (SPD matrix):
- The tensor is symmetric by the Onsager reciprocal relations.
- The tensor is positive definite as the component of the flow parallel to the pressure drop is always in the same direction as the pressure drop.
The permeability tensor is always diagonalizable (being both symmetric and positive definite). The eigenvectors will yield the principal directions of flow, meaning the directions where flow is parallel to the pressure drop, and the eigenvalues representing the principal permeabilities.
Ranges of common intrinsic permeabilities
These values do not depend on the fluid properties; see the table derived from the same source for values of hydraulic conductivity, which are specific to the material through which the fluid is flowing.
| Permeability | Pervious | Semi-Pervious | Impervious | ||||||||||
| Unconsolidated Sand & Gravel | Well Sorted Gravel | Well Sorted Sand or Sand & Gravel | Very Fine Sand, Silt, Loess, Loam | ||||||||||
| Unconsolidated Clay & Organic | Peat | Layered Clay | Fat / Unweathered Clay | ||||||||||
| Consolidated Rocks | Highly Fractured Rocks | Oil Reservoir Rocks | Fresh Sandstone | Fresh Limestone, Dolomite | Fresh Granite | ||||||||
| κ (cm2) | 0.001 | 0.0001 | 10−5 | 10−6 | 10−7 | 10−8 | 10−9 | 10−10 | 10−11 | 10−12 | 10−13 | 10−14 | 10−15 |
| κ (millidarcy) | 10+8 | 10+7 | 10+6 | 10+5 | 10,000 | 1,000 | 100 | 10 | 1 | 0.1 | 0.01 | 0.001 | 0.0001 |
Source: modified from Bear, 1972
See also
- Hydraulic conductivity
- Hydrogeology
- Permeation
- Petroleum geology
- Relative permeability
- Klinkenberg correction
Footnotes
- ^ "CalcTool: Porosity and permeability calculator". www.calctool.org. Retrieved on 2008-05-30.
References
- Bear, Jacob, 1972. Dynamics of Fluids in Porous Media, Dover. — ISBN 0-486-65675-6
- Wang, H. F., 2000. Theory of Linear Poroelasticity with Applications to Geomechanics and Hydrogeology, Princeton University Press. ISBN 0691037469
External links
- Graphical depiction of different flow rates through materials of differing permeability
- Web-based porosity and permeability calculator given flow characteristics
|
||||||||||||||||||||||||||||||||||||||
Wikipedia content modification information:
- This page was last modified on 19 November 2008, at 02:52.
Wikipedia Authorship and Review
Wikipedia content provided here is not reviewed directly by MedLibrary.org. Wikipedia content is authored by an open community of volunteers and is not produced by or in any way affiliated with MedLibrary.org.
Wikipedia Usage Guidelines
This article is licensed under the GNU Free Documentation License. It uses material from the Wikipedia article on "Permeability (fluid)".
The URL for this specific entry is:
All Wikipedia text is available under the terms of the GNU Free Documentation License. (See Copyrights for details). Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc.