This MedLibrary.org supplementary page on Plating is provided directly from the open source Wikipedia as a service to our readers. Please see the note below on authorship of this content, as well as the Wikipedia usage guidelines. To search for other content from our encyclopedia supplement, please use the form below:
Related Sponsors
 |
This article or section is in need of attention from an expert on the subject. WikiProject Chemistry or the Chemistry Portal may be able to help recruit one. If a more appropriate WikiProject or portal exists, please adjust this template accordingly. (November 2008) |
Plating describes surface-covering where a metal is deposited on a conductive surface. Plating has been done for hundreds of years, but it is also critical for modern technology. Plating is used to decorate objects, for corrosion inhibition, to improve solderability, to harden, to improve wearability, to reduce friction, to improve paint adhesion, to alter conductivity, for radiation shielding, and for other purposes. Jewelry typically uses plating to give a silver or gold finish. Thin-film deposition has plated objects as small as an atom, therefore some plating is nanotechnology.
There are several plating methods, and many variations. In one method, a solid surface is covered with a metal sheet, and then heat and pressure are applied to fuse them (a version of this is Sheffield plate). Other plating techniques include vapor deposition under vacuum and sputter deposition. Recently, plating often refers to using liquids. Metallizing refers to coating metal on non-metallic objects.
Contents |
Electroplating
In electroplating, an ionic metal is supplied with electrons to form a non-ionic coating on a substrate. A common system involves a chemical solution with the ionic form of the metal, an anode (positively charged) which may consist of the metal being plated (a soluble anode) or an insoluble anode (usually carbon, platinum, titanium, lead, or steel), and finally, a cathode (negatively charged) where electrons are supplied to produce a film of non-ionic metal.
Electroless plating
Electroless plating, also known as chemical or auto-catalytic plating, is a non-galvanic type of plating method that involves several simultaneous reactions in an aqueous solution, which occur without the use of external electrical power. The reaction is accomplished when hydrogen is released by a reducing agent, normally sodium hypophosphite, and oxidized thus producing a negative charge on the surface of the part. The most common electroless plating method is electroless nickel plating.
Specific cases
Gold plating
Gold plating is a method of depositing a thin layer of gold on the surface of other metal, most often copper or silver.
Gold plating is often used in electronics, to provide a corrosion-resistant electrically conductive layer on copper, typically in electrical connectors and printed circuit boards. With direct gold-on-copper plating, the copper atoms have the tendency to diffuse through the gold layer, causing tarnishing of its surface and formation of an oxide/sulfide layer. A layer of a suitable barrier metal, usually nickel, has therefore to be deposited on the copper substrate, forming a copper-nickel-gold sandwich.
Metals may also be coated with gold for ornamental purposes, using a number of different processes usually referred to as gilding.
Silver plating
For less demanding applications in electronics, silver is often used as a cheaper replacement for gold. Care should be used for parts exposed to high humidity environments. When the silver layer is porous or contains cracks, the underlying copper undergoes rapid galvanic corrosion, flaking off the bell end crust the plating and exposing the copper itself; a process known as red plague.
Historically, silver plate was used to provide a cheaper version of items that might otherwise be made of silver, including cutlery and candlesticks. The earliest kind was Old Sheffield Plate, but in the 19th century new methods of production (including electroplating) were introduced: see Sheffield Plate.
Another method that can be used to apply a thin layer of silver to several objects, such as glass, is the Tollen's Test method, which usually is prepared as follows. Using this method the final reaction can occur by placing Tollen's Reagent in a glass and then adding Glucose/Dextrose and shaking the bottle to perform the reaction.
AgNO3 + KOH -> AgOH + KNO3
AgOH + 2NH3 -> [Ag(NH3)21+ + [OH]1- (Note: See Tollen's Reagent)
[Ag(NH3)21+ + [OH]1- + Aldehyde(Usually Glucose/Dextrose) -> Ag + 2NH3 + H2O
Rhodium plating
Rhodium plating is occasionally used on white gold, silver or copper and its alloys. A barrier layer of nickel is usually deposited on silver first, though in this case it is not to prevent migration of silver through rhodium, but to prevent contamination of the rhodium bath with silver and copper, which slightly dissolve in the sulfuric acid, usually present in the bath composition.
Chrome plating
Chrome plating is a finishing treatment utilizing the electrolytic deposition of chromium. The most common form of chrome plating is the thin, decorative bright chrome, which is typically a 10-µm layer over an underlying nickel plate. When plating on iron or steel, an underlying plating of copper allows the nickel to adhere. The pores (tiny holes) in the nickel and chromium layers also promote corrosion resistance. Bright chrome imparts a mirror-like finish to items such as metal furniture frames and automotive trim. Thicker deposits, up to 1000 µm, are called hard chrome and are used in industrial equipment to reduce friction and wear.
The traditional solution used for industrial hard chrome plating is made up of about 250 g/l of Cr03 and about 2.5 g/l of S04-. In solution, the chrome exists as chromic acid, known as hexavalent chromium. A high current is used, in part to stabilize a thin layer of chromium(+2) at the surface of the plated work. Acid chrome has poor throwing power, fine details or holes are further away and receive less current resulting in poor plating.
Zinc plating
Zinc coatings prevent oxidation of the protected metal by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not cause a breakdown of the substrate's surface integrity as it is formed. Indeed the zinc oxide, if undisturbed, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers.
Tin plating
- See also: Tinplate
The tin-plating process is used extensively to protect both ferrous and nonferrous surfaces. Tin is a useful metal for the food processing industry since it is non-toxic, ductile and corrosion resistant. The excellent ductility of tin allows a tin coated base metal sheet to be formed into a variety of shapes without damage to the surface tin layer. It provides sacrificial protection for copper, nickel and other non-ferrous metals, but not for steel.
Tin is also widely used in the electronics industry because of its ability to protect the base metal from oxidation thus preserving its solderability. In electronic applications, lead may be added to prevent the growth of metallic "whiskers" in compression stressed deposits, which would otherwise cause electrical shorting
Alloy plating
In some cases, it is desirable to co-deposit two or more metals resulting in an electroplated alloy deposit. Depending on the alloy system, an electroplated alloy may be solid solution strengthened or precipitation hardened by heat treatment to improve the plating's physical and chemical properties. Nickel-Cobalt is a common electroplated alloy.
Composite plating
Metal matrix composite plating can be manufactured when a substrate is plated in a bath containing a suspension of ceramic particles. Careful selection of the size and composition of the particles can fine-tune the deposit for wear resistance, high temperature performance, or mechanical strength. Tungsten Carbide, Silicon carbide, Chromium carbide, and Aluminum Oxide (alumina) are commonly used in composite electroplating.
Cadmium plating
Cadmium plating is under scrutiny because of the environmental toxicity of the cadmium metal. However, cadmium plating is still widely unreplaced in some applications such as aerospace fasteners and it remains in military and aviation specs.1 Cadmium plating (or "cad plating") has technical advantages such as excellent corrosion resistance even at relatively low thickness and in salt atmospheres, can be dyed to many colors and clear, has good lubricity and solderability, and works well either as a final finish or as a paint base. 2
See also
References
- ^ Cad plating letters-to-the-editor from http://www.finishing.com/136/09.shtml
- ^ Cadmium plating fact sheet from the Erie Plating Company, available http://erieplating.com/cadmium-plating (used with their permission).
Wikipedia content modification information:
- This page was last modified on 21 November 2008, at 23:44.
Wikipedia Authorship and Review
Wikipedia content provided here is not reviewed directly by MedLibrary.org. Wikipedia content is authored by an open community of volunteers and is not produced by or in any way affiliated with MedLibrary.org.
Wikipedia Usage Guidelines
This article is licensed under the GNU Free Documentation License. It uses material from the Wikipedia article on "Plating".
The URL for this specific entry is:
All Wikipedia text is available under the terms of the GNU Free Documentation License. (See Copyrights for details). Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc.