Ripple (fluid dynamics)

This MedLibrary.org supplementary page on Ripple (fluid dynamics) is provided directly from the open source Wikipedia as a service to our readers. Please see the note below on authorship of this content, as well as the Wikipedia usage guidelines. To search for other content from our encyclopedia supplement, please use the form below:

Related Sponsors

BM Pharmacy Generic pharmaceuticals at unbeatable prices. Insomnia, men's health, hair health, pain control. bmpharmacy.com

Online Pharmacy Carisoprodol, tadalafil, sildenafil, vardenafil and more... xlpharmacy.com

MedBasket.com Discreet. Inexpensive. Fast shipping. Great selection. What more can we say? medbasket.com

Frugalmed 2000 reasons to shop with us first. frugalmed.com

Ads by Tiva

This article is about ripples on fluid interfaces. For ripples in electricity, see ripple (electrical). For other uses, see ripple.

Ripples on Lifjord in Øksnes, Norway.

Capillary waves produced by droplet impacts on the interface between water and air.

A capillary wave is a wave travelling along the interface between two fluids, whose dynamics are dominated by the effects of surface tension. Capillary waves are common in nature and home, and are often referred to as ripple. The wavelength of capillary waves is typically less than a few centimeters.

A gravity–capillary wave on a fluid interface is influenced by both the effects of surface tension and gravity, as well as by the fluid inertia.

1 Capillary waves, proper
2 Gravity–capillary waves
3 See also
4 Gallery
5 Notes
6 References
7 External links

Capillary waves, proper

The dispersion relation for capillary waves is

$\omega^2=\frac{\sigma}{\rho+\rho'}\, |k|^3,$

where ω is the angular frequency, σ the surface tension, ρ the density of the heavier fluid, ρ' the density of the lighter fluid and k the wavenumber. The wavelength is $\lambda=\frac{2 \pi}{k}.$

Gravity–capillary waves

Dispersion of gravity–capillary waves on the surface of deep water (zero mass density of upper layer, ρ′ = 0). Phase and group velocity divided by $\scriptstyle \sqrt[4]{g\sigma/\rho}$ as a function of inverse relative wavelength $\scriptstyle \frac{1}{\lambda}\sqrt{\sigma/(\rho g)}$ .
Blue lines (A): phase velocity, Red lines (B): group velocity.
Drawn lines: dispersion relation for gravity–capillary waves.
Dashed lines: dispersion relation for deep-water gravity waves.
Dash-dot lines: dispersion relation valid for deep–water capillary waves.

In general, waves are also affected by gravity and are then called gravity–capillary waves. Their dispersion relation reads, for waves on the interface between two fluids of infinite depth:¹²

$\omega^2=|k|\left( \frac{\rho-\rho'}{\rho+\rho'}g+\frac{\sigma}{\rho+\rho'}k^2\right),$

where g is the acceleration due to gravity, ρ and ρ‘ are the mass density of the two fluids (ρ > ρ‘). Notice the factor $(ρ - ρ') / (ρ + ρ')$ in the first term is the Atwood number.

Gravity wave regime

Further information: Airy wave theory

For large wavelengths (small k = 2π/λ), only the first term is relevant and one has gravity waves. In this limit, the waves have a group velocity half the phase velocity: following a single wave's crest in a group one can see the wave appearing at the back of the group, growing and finally disappearing at the front of the group.

Capillary wave regime

Shorter (large k) waves (e.g. 2 mm), which are proper capillary waves, do the opposite: an individual wave appears at the front of the group, grows when moving towards the group center and finally disappears at the back of the group. Phase velocity is two thirds of group velocity in this limit.

Phase velocity minimum

Between these two limits, an interesting and common situation occurs when the dispersion caused by gravity cancels out the dispersion due to the capillary effect. At a certain wavelength, the group velocity equals the phase velocity, and there is no dispersion. At precisely this same wavelength, the phase velocity of gravity-capillary waves as a function of wavelength (or wave number) has a minimum. Waves with wavelengths much smaller than this critical wavelength λ_c are dominated by surface tension, and much above by gravity. The value of this wavelength is¹:

$\lambda_c = 2 \pi \sqrt{ \frac{\sigma}{(\rho-\rho') g}}.$

For the air–water interface, λ_c is found to be 1.7 cm¹.

Derivation

As Richard Feynman put it, "[water waves] that are easily seen by everyone and which are usually used as an example of waves in elementary courses [...] are the worst possible example [...]; they have all the complications that waves can have."³ The derivation of the general dispersion relation is therefore quite involved.⁴

Therefore, first the assumptions involved are pointed out. There are three contributions to the energy, due to gravity, to surface tension, and to hydrodynamics. The first two are potential energies, and responsible for the two terms inside the parenthesis, as is clear from the appearance of g and σ. For gravity, an assumption is made of the density of the fluids being constant (i.e., incompressibility), and likewise g (waves are not high for gravitation to change appreciably). For surface tension, the deviations from planarity (as measured by derivatives of the surface) are supposed to be small. Both approximations are excellent for common waves.

The last contribution involves the kinetic energies of the fluids, and is the most involved. One must use a hydrodynamic framework to tackle this problem. Incompressibility is again involved (which is satisfied if the speed of the waves is much less than the speed of sound in the media), together with the flow being irrotational — the flow is then potential; again, these are typically good approximations for common situations. The resulting equation for the potential (which is Laplace equation) can be solved with the proper boundary conditions. On one hand, the velocity must vanish well below the surface (in the "deep water" case, which is the one we consider, otherwise a more involved result is obtained, see Ocean surface waves.) On the other, its vertical component must match the motion of the surface. This contribution ends up being responsible for the extra k outside the parenthesis, which causes all regimes to be dispersive, both at low values of k, and high ones (except around the one value at which the two dispersions cancel out.)

Dispersion relation for gravity–capillary waves on an interface between two semi–infinite fluid domains

Consider two fluid domains, separated by an interface with surface tension. The mean interface position is horizontal. It separates the upper from the lower fluid, both having a different constant mass density, ρ and ρ’ for the lower and upper domain respectively. The fluid is assumed to be inviscid and incompressible, and the flow is assumed to be irrotational. Then the flows are potential, and the velocity in the lower and upper layer can be obtained from ∇Φ and ∇Φ’, respectively. Here Φ(x,y,z,t) and Φ’(x,y,z,t) are velocity potentials.

Three contributions to the energy are involved: the potential energy V_g due to gravity, the potential energy V_st due to the surface tension and the kinetic energy T of the flow. The part V_g due to gravity is the simplest: integrating the potential energy density due to gravity, ρ g z (or ρ’ g z) from a reference height to the position of the surface, z = η(x,y,t)⁵:

$V_\mathrm{g} = \iint dx\, dy\; \int_0^\eta dz\; (\rho - \rho') g z = \frac{1}{2} (\rho-\rho') g \iint dx\, dy\; \eta^2,$

assuming the mean interface position is at z=0.

An increase in area of the surface causes a proportional increase of energy due to surface tension⁶:

$V_\mathrm{st} = \sigma \iint dx\, dy\; \left[ \sqrt{ 1 + \left( \frac{\partial \eta}{\partial x} \right)^2 + \left( \frac{\partial \eta}{\partial y} \right)^2} - 1 \right] \approx \frac{1}{2} \sigma \iint dx\, dy\; \left[ \left( \frac{\partial \eta}{\partial x} \right)^2 + \left( \frac{\partial \eta}{\partial y} \right)^2 \right],$

where the first equality is the area in this (Monge's) representation, and the second applies for small values of the derivatives (surfaces not too rough).

The last contribution involves the kinetic energy of the fluid⁷:

$T= \frac{1}{2} \iint dx\, dy\; \left[ \int_{-\infty}^\eta dz\; \rho\, \left| \bold\nabla \Phi \right|^2 + \int_\eta^{+\infty} dz\; \rho'\, \left| \bold\nabla \Phi' \right|^2 \right].$

Use is made of the fluid being incompressible and its flow is irrotational (often, sensible approximations). As a result, both Φ(x,y,z,t) and Φ’(x,y,z,t) must satisfy the Laplace equation⁸:

$\nabla^2 \Phi = 0$ and $\nabla^2 \Phi' = 0.$

These equations can be solved with the proper boundary conditions: Φ and Φ’ must vanish well away from the surface (in the "deep water" case, which is the one we consider).

Using Green's identity, and assuming the deviations of the surface elevation to be small (so the z–integrations may be approximated by integrating up to z=0 instead of z=η), the kinetic energy can be written as⁷:

$T \approx \frac{1}{2} \iint dx\, dy\; \left( \rho\, \Phi\, \frac{\partial \Phi }{\partial z}\; -\; \rho'\, \Phi'\, \frac{\partial \Phi'}{\partial z} \right).$

To find the dispersion relation, it is sufficient to consider a sinusoidal wave on the interface, propagating in the x–direction⁶:

$\eta = a\, \cos\, ( kx - \omega t) = a\, \cos\, \theta ,$

with amplitude a and wave phase θ = kx - ωt. The kinematic boundary condition at the interface, relating the potentials to the interface motion, is that the vertical velocity components must match the motion of the surface⁶:

$\frac{\partial\Phi}{\partial z} = \frac{\partial\eta}{\partial t}$ and $\frac{\partial\Phi'}{\partial z} = \frac{\partial\eta}{\partial t}$ at z = 0.

To tackle the problem of finding the potentials, one may try separation of variables, when both fields can be expressed as⁶:

$\begin{align} \Phi(x,y,z,t) & = + \frac{1}{|k|} \text{e}^{+|k|z}\, \omega a\, \sin\, \theta, \\ \Phi'(x,y,z,t)& = - \frac{1}{|k|} \text{e}^{-|k|z}\, \omega a\, \sin\, \theta. \end{align}$

Then the contributions to the wave energy, horizontally integrated over one wavelength λ = 2π/k in the x–direction, and over a unit width in the y–direction, become⁶⁹:

$\begin{align} V_\text{g} &= \frac{1}{4} (\rho-\rho') g a^2 \lambda, \\ V_\text{st} &= \frac{1}{4} \sigma k^2 a^2 \lambda, \\ T &= \frac{1}{4} (\rho+\rho') \frac{\omega^2}{|k|} a^2 \lambda. \end{align}$

The dispersion relation can now be obtained from the Lagrangian L = T - V, with V the sum of the potential energies by gravity V_g and surface tension V_st¹⁰:

$L = \frac{1}{4} \left[ (\rho+\rho') \frac{\omega^2}{|k|} - (\rho-\rho') g - \sigma k^2 \right] a^2 \lambda.$

For sinusoidal waves and linear wave theory, the phase–averaged Lagrangian is always of the form L = D(ω,k) a², so that variation with respect to the only free parameter, a, gives the dispersion relation D(ω,k) = 0 ¹⁰. In our case D(ω,k) is just the expression in the square brackets, so that the dispersion relation is:

$\omega^2 = |k| \left( \frac{\rho-\rho'}{\rho+\rho'}\, g + \frac{\sigma}{\rho+\rho'}\, k^2 \right),$

the same as above.

As a result, the average wave energy per unit horizontal area, ( T + V ) / λ, is:

$\bar{E} = \frac{1}{2}\, \left[ (\rho-\rho')\, g + \sigma k^2 \right]\, a^2.$

As usual for linear wave motions, the potential and kinetic energy are equal (equipartition holds): T = V.¹¹

Gallery

Ripples on water

Ripples on water created by water striders

Ripples of tapwater over a plughole

Notes

^ ^a ^b ^c Lamb (1994), §267, page 458–460.
^ Dingemans (1997), Section 2.1.1, p. 45.
Phillips (1977), Section 3.2, p. 37.
^ R.P. Feynman, R.B. Leighton, and M. Sands (1963). The Feynman Lectures on Physics. Addison-Wesley. Volume I, Chapter 51-4.
^ See e.g. Safran (1994) for a more detailed description.
^ Lamb (1994), §174 and §230.
^ ^a ^b ^c ^d ^e Lamb (1994), §266.
^ ^a ^b Lamb (1994), §61.
^ Lamb (1994), §20
^ Lamb (1994), §230.
^ ^a ^b Whitham, G.B. (1974). Linear and nonlinear waves, Wiley-Interscience. ISBN 0 471 94090 9. See section 11.7.
^ Lord Rayleigh (J. W. Strutt) (1877). "On progressive waves". Proceedings of the London Mathematical Society 9: 21–26. doi:10.1112/plms/s1-9.1.21. Reprinted as Appendix in: Theory of Sound 1, MacMillan, 2^nd revised edition, 1894.

References

Dingemans, M. W. (1997). Water wave propagation over uneven bottoms. Advanced Series on Ocean Engineering. 13, World Scientific, Singapore. pp.2 Parts, 967 pages. ISBN 981-02-0427-2.
Lamb, H. (1994). Hydrodynamics (6^th edition ed.), Cambridge University Press. ISBN 9780521458689.
Phillips, O. M. (1977). The dynamics of the upper ocean (2^nd edition ed.), Cambridge University Press. ISBN 0-521-29801-6.
Safran, Samuel (1994). Statistical thermodynamics of surfaces, interfaces, and membranes, Addison-Wesley.
Tufillaro, N. B.; Ramshankar, R.; Gollub, J. P. (1989), "Order-disorder transition in capillary ripples", Physical Review Letters 62 (4): 422

External links

Capillary waves entry at sklogwiki

Wikipedia content modification information:

This page was last modified on 25 November 2008, at 19:20.

Wikipedia Authorship and Review

Wikipedia content provided here is not reviewed directly by MedLibrary.org. Wikipedia content is authored by an open community of volunteers and is not produced by or in any way affiliated with MedLibrary.org.

Wikipedia Usage Guidelines

This article is licensed under the GNU Free Documentation License. It uses material from the Wikipedia article on "Ripple (fluid dynamics)".

The URL for this specific entry is:

http://medlibrary.org/medwiki/Ripple_(fluid_dynamics)

All Wikipedia text is available under the terms of the GNU Free Documentation License. (See Copyrights for details). Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc.

Welcome to the MedLibrary.org Wikipedia Supplement on Ripple (fluid dynamics) -- Please Click to Return to Front Page