This MedLibrary.org supplementary page on Triaxial shear test is provided directly from the open source Wikipedia as a service to our readers. Please see the note below on authorship of this content, as well as the Wikipedia usage guidelines. To search for other content from our encyclopedia supplement, please use the form below:
Related Sponsors
A triaxial shear test is a common method to measure the mechanical properties of many deformable solids, especially soil, sand, clay, and other granular materials or powders. There are several variations on the test, discussed below.
Contents |
Basic Concept
For loose granular materials like sand or soil, the material is contained in a cylindrical latex sleeve with a flat, circular metal plate or platen closing off the top and bottom ends. This cylinder is placed into a bath of water to provide pressure along the sides of the cylinder. The top platen can then be mechanically driven up or down along the axis of the cylinder to squeeze the material. The distance that the upper platen travels is measured as a function of the force required to move it, as the pressure of the surrounding water is carefully controlled. The net change in volume of the material is also measured by how much water moves in or out of the surrounding bath.
The principle behind a triaxial shear test is that the stress applied in the vertical direction (along the axis of the cylinder) can be different than the stress applied in the horizontal directions (along the sides of the cylinder). This produces a non-hydrostatic stress state, which contains shear stress.
A solid is defined as a material that can support shear stress without moving. However, every solid has an upper limit to how much shear stress it can support. The triaxial tester is designed to measure that limit. The stress on the platens is increased until the material in the cylinder fails and forms sliding regions within itself, known as shear bands. A motion where a material is deformed under shear stress is known as shearing. The geometry of the shearing in a triaxial tester typically causes the sample to become shorter while bulging out along the sides. The stress on the platen is then reduced and the water pressure pushes the sides back in, causing the sample to grow taller again. This cycle is usually repeated several times while collecting stress and strain data about the sample.
During the shearing, a granular material will typically have a net gain or loss of volume. If it had originally been in a dense state, then it typically gains volume, a characteristic known as Reynolds' dilatancy. If it had originally been in a very loose state, then compaction may occur before the shearing begins or in conjunction with the shearing.
From the triaxial test data, it is possible to extract fundamental material parameters about the sample, including its angle of internal friction, apparent cohesion, and dilatancy angle. These parameters are then used in computer models to predict how the material will behave in a larger-scale engineering application. An example would be to predict the stability of the soil on a slope, whether the slope will collapse or whether the soil will support the shear stresses of the slope and remain in place. Triaxial tests are used along with other tests to make such engineering predictions.
Types of Triaxial Tests
There are several variations on the basic concept of triaxial testing. These are given the following labels (corresponding test standard in parentheses):
- CD — Consolidated drained
- CU — Consolidated undrained (ASTM D4767)
- UU — Unconsolidated undrained (ASTM D2850)
References
- Holtz, R. and Kovacs, W. (1981), An Introduction to Geotechnical Engineering, Prentice-Hall, Inc. ISBN 0-13-484394-0
- Head, K.H. (1998), Effective Stress Tests, Volume 3, Manual of Soil Laboratory Testing, 2nd Edition, John Wiley & Sons. ISBN 0-471-97795-0.
See also
- Geotechnical engineering
- Soil mechanics
- Civil engineering
- Effective stress
- Earthworks
- Granular material
- Important publications in geotechnical engineering
|
||||||||||||||||||||||||||||||||||||||
Wikipedia content modification information:
- This page was last modified on 22 October 2008, at 04:44.
Wikipedia Authorship and Review
Wikipedia content provided here is not reviewed directly by MedLibrary.org. Wikipedia content is authored by an open community of volunteers and is not produced by or in any way affiliated with MedLibrary.org.
Wikipedia Usage Guidelines
This article is licensed under the GNU Free Documentation License. It uses material from the Wikipedia article on "Triaxial shear test".
The URL for this specific entry is:
All Wikipedia text is available under the terms of the GNU Free Documentation License. (See Copyrights for details). Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc.